Webmail  e-Timesheet

Engineering Services

The scope of services offered by MOFS cover Feasibility Studies, Conceptual Engineering, Front End Engineering Design (FEED), Detail Engineering Design, Drafting Services, PDMS Modelling, Project Management Consultant (PMC) and Engineering, Procurement and Construction Management (EPCM). Our Engineering disciplines includes the following:

PROCESS • Process System Simulation
• PFDs, UFDs and P & IDs Development
• Safe Chart and Cause & Effect Matrix
• Process Flare/Venting Study
• Safety Case
• HAC Preparation
• Facilitate Dynamic Simulation
• Start-Up, Commissiong & Operating Procedures
• System Design and Sizing, i.e. - Compressor Station
- Gas Dehydration - CO2 Removal System - De-Bottlenecking
• HAZOP / HAZID / SIL session
• As-Built Exercise
MECH/PIPING • Rotating & Static Equipment Design and Sizing
• Preparation of Specifications and TBE / VDI / VDR
• Equipment Layouts and Elevations
• Safety Escape Route and Safety Appliances Drawings
• PDMS Modelling and Piping Design
• Pipe Stress Analysis and Pipe Supports Selection (Static & Dynamic)
• Material Handling Study
• HVAC System Design
• Piping and Equipment Weight Estimate
• Consolidated MTO and Costing
• Upgrade and Modification Work
• As-Built Exercise
INSTRUMENTATION / TELECOMMUNICATION • Distributed Control System (DCS)
• Safety Instrumented System (SIS) and Fire & Gas System (FGS)
• SCADA and Remote Operation System
• Programmable Logic Controller (PLC) System
• Operator Interface (OI) Human Machine Interface (HMI)
• Electronic Flow Measurement/Metering/Custody Transfer
• Instrument Sizing and Calculation
• Data Communications System & Networking for SCADA
• Telecom Design – Microwave, Fiber Optic, Ratio, etc
• Path Propagation and Coverage Studies
• Control System Optimization Studies and Analysis
• Consolidated MTO and Costing (CAPEX & OPEX)
• Preparation of Specifications and TBE / VDI / VDR
• Upgrade and Modification Work
• As-Built Exercise
ELECTRICAL • System Design and Sizing
• Preparation of Specifications and TBE / VDI / VDR
• Electrical Generation and Distribution System
• Load Analysis and Power System Analysis
• MV & LV Power Generation System Design
• HV / MV & LV Distribution System Design
• Layouts (lighting, cable routing, cable tray & equipment)
• Earthing System and Layout Design
• Navigation Aid System Design
• UPS System Design
• Consolidated MTO and Costing
• Upgrade and Modification Work
• As-Built Exercise
CIVIL / STRUCTURAL / ARCHITECTURAL • Topsides Design Analysis
- In-Place - Load-out - Transportation - Lifting
• Substructure Design Analysis
• Launch (dynamic & static) - Fatigue (dynamic spectral & deterministic) - Upending and Flotation - On-Bottom
• Living Quarters Design + Helideck
• Consolidated MTO and Costing
• Upgrade and Modification Work
• Decommisioning Study
• As-Built Exercise
PIPELINE • Regulatory
• Techno-Economic Studies
• FEED & Conceptual Engineering
• Pipeline Design & Verification
• Pipelay & Tow Installation Engineering
• Riser & J-tube Analysis
• HDD Technology & Shore Approaches
• Intervention and Mitigation for Buckling
• Specification Development
• Procurement & Expediting
• Commissioning
• Interface to facilities
MARINE & NAVAL ARCHITECTURE • Riser Engineering (Flexible & Umbilicals)
• Hydrodynamics
• Mooring Analysis (static, quasi-static,dynamic and fatigue)
• Stability Analysis (intact and damage)
• Ship Design
ASSET INTEGRITY • Reliability Centerd Maintenance (RCM)
• Risk based Inspection
• Risk & Safety Studies
• Process Safety Management
• In service inspection
• Process Safety Management
 
©2018 MOFS. All rights reserved.
MIE OFFSHORE SOLUTIONS SDN BHD (1004204-P) T6-2-2 & T6-3-2 TOWER 6 MAJU LINK
JALAN LINGKARAN TENGAH II (MRR2) 57100 BANDAR TASIK SELATAN KUALA LUMPUR, MALAYSIA